If you’re an avid player of music and audio, you know that every amp is not created equal. Some are great, some are okay, and some are just downright terrible. When it comes to amplifiers, the same rule applies: the more wattage, the better. The more wattage an amp has, the more powerful it is. The more powerful an amp is, the louder it can play music. Except for certain amps, amps with more wattage are not always better. It all comes down to the equipment used to power the amp and the quality of the components used to make it. All of this depends on the level of power needed by the amp, and the quality of the components used to make it. That being said, there are best amps that produce the right amount of power required by your equipment. Keep reading to find out which is the best amp for your gear.
Quick table with our top 3 picks:
Top 9 Best 2500 Watt Amp Reviewed
- Complete 4 Gauge Amplifier Install Kit
- New and Improved Design with Upgraded Fuse Holder and Increased Wire Strands
- Peak Power Rating: 2500 Watts
- Includes Speaker Wire and Twisted Pair RCA Cables
- Includes Installation Accessories and Wire Loom
- 2,500 watts max
- 1,250 watts x 1 at 2 ohms
- 625 watts x 1 at 4 ohms
- Frequency response: 10 Hz to 500 Hz
- Super Class D technology powered by Ultra-Fi MOSFETs for high power, efficient cooling with minimal distortion
- Rockville RVA-M2 2500w Peak/625w Dyno-Certified RMS @ 1 Ohm Amplifier Mono Car Amp+Remote. Metal Bass Remote Included. Dyno Certified RMS Power Ratings: (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc).
- 1 Ohm: 625 Watts(<1% THD @ 14.4 Volts) (70.2% efficient). 2 Ohm: 440 Watts (<1% THD @ 14.4 Volts) (82.4% efficient). 4 Ohm: 264 Watts (<1% THD @ 14.4 Volts) (83.7% Efficient). Peak: (Use these ratings when comparing with the top budget brands such as Boss, Power Acoustik, etc).
- 1 Ohm: 2500 Watts. High-Speed MOSFET Power Supply. Class D Technology. Fully Adjustable 12dB / Octave Crossover with Differential Circuitry. Low Pass Filter: 32Hz - 300Hz. Subsonic Filter: 10Hz - 50Hz. Phase Control Switch. Full IC-Controlled Protection Circuitry.
- Adjustable 0-12dB Bass Equalizer. Mute and Delay Soft Start System. Status Mode LED Indicator. Minimum THD at Rated Power: <0.1%. S/N Ratio: >90dB. Under Voltage Protection at 9V. Over Voltage Protection at 16V. Radiation cooling keeps the amp running at high volumes for hours straight.
- Extruded aluminum heatsink. Frequency Response: 10Hz - 300Hz. Damping Factor: >150 @ 100Hz. Fuse: 30A*2. Technology: This series uses a reliable Class D circuitry that gives you the most reliability and the most power for your money. Dimensions: (L x W x H) 13" x 8.5" x 2.24". Weight: 7 lbs
- 4 Gauge Blue CCA (Copper Clad Aluminum) Power Wire: 17 Feet / Black CCA (Copper Clad Aluminum) Ground Wire: 3 Feet
- 18 Gauge Blue Remote Wire: 17 Feet | CCA is Less Conductive than OFC Wire!
- 20 Feet FT / 16 GA Speaker Wire | Thick In-Line AGU Fuse Holder/ 80 & 100 Amp ANL Fuse
- True Sound 17 Feet FT Double Shielded RCA Cable | Complete Installation Accessories included
- Wire Gauge Set To International Wire Gauge (exceeds Standard AWG).
- Power: 2500 watts max X 1 @1-ohm, 1250 watts max X 1 @2-ohms, 625 watts max X 1 @4-Ohms
- Class D: power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until it’s needed instead of being converted into heat. Reduction in size/weight, reduced power waste, smaller heat sink, compact circuitry
- 1 ohm stable: able to continuously power loads of 1 ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be able to perform the way they were made to
- Variable subsonic filter: to prevent your subwoofer(s) from bottoming out, the variable subsonic filter filters out frequencies below the subwoofer(s) specified low frequency limits and allows the driver to reach a maximum safe excursion
- Variable low-pass crossover: subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction
- Features – The 4 channel bass boost amplifier has features like - Frequency Response: 10HZ-30KHZ, Remote Bass Knob, 2-way protection, hi/low pass crossovers, hi/low level inputs, MOSFET Power Supply, Thermal Protection, Gain Control, 2 Ohm Stable
- Class A/B – This multichannel subwoofer amplifier exhibits a Class A/B topology. In the presence of no audio signal, Class A Amplifier has a high amount of current flowing in its output while Class b amplifier has no current flowing.
- Quality - This Class A/B 4 channel amplifier exhibits quality frequency response rates and crossover network which places this amp at a prominent place. Durable design and highly efficient performance makes this subwoofer amp for car speakers stand out amongst the others.
- Power – This Class A/B 2500 watt Amplifier has a power rating distribution as followed 625 X 4 MAX @ 2 OHMS. The 4 channel amplifier for car speakers also provides a 2-way protection circuitry as a part of its design.
- Low/High Level Inputs – The multichannel amplifier for car speakers come with low/high level inputs. A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your speakers
- POWERFUL SOUND: Deliver powerful sound to your speakers and subwoofers with this Super D Class, 2,500-watt, mono car audio amplifier; Wired bass remote included
- OPERATION: Control your sound with mono only operation, variable electronic crossover, and electronic equalizer capabilities; Monitor overload and speaker short protection with illuminated indicators on the amplifier end panel
- OUTPUT TECHNOLOGY: Ultra-Fi MOSET output device technology and classic Hifonics aluminum construction for powerful sound, efficient cooling, and minimal distortion
- CONNECTORS: Secure molded connection terminal with easy-to-access, angled ports for all power, ground, and speaker connections and high-temperature, impact-resistant, nickel-plated connectors; Nickel-plated connectors deliver efficient high/low level audio, crisp sound, while providing a secure and erosion-resistant seal
- POWER: Power ratings: @ 1 ohms - 1 channel x 2,500 watts; @ 2 ohms - 1 channel x 1,250 watts; @ 4 ohms - 1 channel x 625 watts; Dual coil Pulse Width Modulated power supply keeps voltage constant through Ultra-Fi output devices
- High quality thick 17 feet ft 4 gauge GA power cable
- Premium 3 feet ft 4 gauge GA ground cable/ inline agu fuse holder & 100a fuse included!
- True sound 17 feet ft Double shielded RCA cable
- High quality 17 feet ft/ 18 ga turn-on cable & 20 feet ft/ 16 ga speaker wire
- All accessories/ terminal included! Perfect for any installer shop, great for car/ truck/ motorcycle/ RV/ ATV
- High quality thick 17 feet ft 4 gauge GA power cable
- Premium 3 feet ft 4 gauge GA ground cable/ inline agu fuse holder & 80a + 100a fuse included!
- True sound 17 feet ft Double shielded RCA cable (two dual rca's + 1 single RCA)
- High quality 17 feet ft/ 18 ga turn-on cable & 20 feet ft/ 16 ga speaker wire
- All accessories/ terminal included! Perfect for any installer shop, great for car/ truck/ motorcycle/ RV/ ATV
Buying Guide For The Best 2500 Watt Amp
Pay Attention to the Amp’s Power Rating
One of the most important things to look at when buying an amp is the power rating. The power rating is a unit of measurement that tells you how much power an amp can produce. Depending on the wattage, you will want to pay attention to what type of equipment you want to use with it. An amp with a high wattage can put out more power than one with a lower wattage and vice versa.
Keep in Mind the Noise Made by the Amp
Noise is one of the worst enemies of an amplifier. It can be a nuisance when you’re trying to have a good time, or even when you are trying to study or work. Amplifiers can produce noise in order to reproduce sound, but they should not produce too much noise that affects your health. If you feel like an amp is making too much noise, try using an equalizer or reducing the volume on your device so that it can still be heard but not as loud as it originally was before turning on the amplifier. Some amps are more powerful than others and may emit more noise than others.
Look for an Amp That Is Stable
An amplifier is not only a piece of electronic equipment that is used to amplify sound; it’s also a piece of equipment that can be used for other purposes. If you have an amp that does not have a stable signal, then it will produce noise, and you will not be able to use the amp for what it was meant for.
Know How to Test the Amp
You can test your amp by using a multimeter (an electrical device with two probes) and checking whether the voltage levels are within specifications. You should also check whether the current levels are within specifications as well. The multimeter will be able to tell you whether or not your amp is producing enough voltage or current levels and that it has been doing so for a long time without failing. It will also be able to tell you if there is any power coming into your device while you’re testing it, which can be useful in case there is something wrong with the power source that you’re using when testing your amplifier.
Make Sure You Have Enough Power Sources for Your Amplifier
An amplifier usually requires some form of power source in order for it to work. This means that you should have a good power source and enough of it to power your amplifier. You should also make sure that the power source is stable and reliable so that you will not have any problems with your amplifier. There are some amplifiers that do not require the use of an external power source, but most do.
Check Whether Your Amplifier Is Being Overheated
It’s normal for amplifiers to get heated up when they’re being used and if this happens, then it will produce noise on its own as well as heat up the device that’s being used with it. If you want to prevent this from happening, then try using an amplifier cooler or heatsink to eliminate the heat from your amplifier. You can also use an external fan for extra cooling if you want to reduce the noise produced by your amp when it gets hot. It is also recommended that you disconnect your amp from other devices when it is getting hot, as that can cause it to overheat and produce noise.
Conclusion
Now that you know a little bit about the basics of car audio systems, what’s the best amp for power output? It’s important to select the amp that best suits your needs. If you’re looking for an amp to power your speakers, then you’ll need to consider the speaker power ratings and how much power is going to be needed. However, if you’re looking for an amp for subwoofers, then you’ll need a completely different amp.
